Product name:Mechanical encryption soft seal gate valve
Product model:FDZ45X-10/16
Product features
The product appearance and general valve, just inside the stem with the covert clutch device, need to unscrew the wheel bolt is fixed, the special key is inserted into the bolt holes to adjust the on-off state, then the operating handwheel switch valve, the operation is finished, and then screwed on the bolt can be fixed hand-wheel. Because the product look from the exterior with ordinary valves are exactly the same, so mysterious.
The product fully mechanical device, open and close to any location can realize self locking, simple, durable, not easy to be damaged, the anti-theft effect is excellent, without a special key cannot open, mounted on a tap water pipeline, heating pipe or other conduit can effectively avoid the stealing phenomenon, very easy to manage.
Technical parameters
Model | FDZ45X-10 | FDZ45X-16 |
Nominal pressure | 1.0MPa (10kgf/cm2) | 1.6MPa (16kgf/cm2) |
Nominal diameter | 40 - 400mm | 40 - 400mm |
Seal test pressure | 1.1MPa (11kgf/cm2) | 1.76MPa (17.6kgf/cm2) |
Strength test pressure | 1.5MPa (15kgf/cm2) | 2.4MPa (24kgf/cm2) |
Applicable temperature | ≤ 120 ℃ | ≤ 120 ℃ |
Applicable medium | Water, oil, plumbing and other non corrosive fluid | Water, oil, plumbing and other non corrosive fluid |
Drive mode | Manual | Manual |
Can also be based on customer requirements, provide specific technical parameters of the product |
Scope of application
Can be used in urban water supply and drainage, Water Management District, district heating management, landscaping, oil and other industries.
Valve sheet of material
Valve body | Grey cast iron, ductile cast iron |
Gate | Grey cast iron, ductile cast iron, NBR, EPDM, HTV |
Valve cover | Grey cast iron, ductile cast iron |
Hand wheel | Carbon steel, grey cast iron, ductile cast iron |
Valve stem | Stainless steel |
Sealing sleeve | Brass |
Valve stem nut | Brass |
Sealing ring | NBR, HTV |
Manufacturing specification
Valve structure length consistent with GB/T 12221-1989 short series; valve connecting flange size DN40 ~ 500mm drill press GB/T 17241.6-1998 standards, DN40 ~ 200mm outer diameter of the flange made according to standard PN10/16, DN250 ~ 500mm outer diameter of the flange is in line with the PN16 standard; pressure test in accordance with GB/T 13927-1992 requirements.
Data sheet(unit: mm)
Nominal diameter (DN) | Structure length | H | Bolt | |
10Kg | 16Kg | Reference weight kg |
Bolt hole center circle diameter D | Bolt hole diameter | Number | Thread specification | Bolt hole center circle diameter D | Bolt hole diameter | Number | Thread specification |
40 | 165 | 170 | 110 | 19 | 4 | M16 | 110 | 19 | 4 | M16 | 7 |
50 | 178 | 185 | 125 | 19 | 4 | M16 | 125 | 19 | 4 | M16 | 9 |
65 | 190 | 205 | 145 | 19 | 4 | M16 | 145 | 19 | 4 | M16 | 12 |
80 | 203 | 310 | 160 | 19 | 8 | M16 | 160 | 19 | 8 | M16 | 20 |
100 | 229 | 340 | 180 | 19 | 8 | M16 | 180 | 19 | 8 | M16 | 27 |
150 | 267 | 430 | 240 | 23 | 8 | M20 | 240 | 23 | 8 | M20 | 50 |
200 | 292 | 520 | 295 | 23 | 8 | M20 | 295 | 23 | 12 | M20 | 80 |
250 | 330 | 545 | 350 | 23 | 12 | M20 | 355 | 28 | 12 | M24 | 120 |
300 | 356 | 660 | 400 | 23 | 12 | M20 | 410 | 28 | 12 | M24 | 160 |
400 | 406 | 915 | 515 | 28 | 16 | M24 | 525 | 31 | 16 | M27 | 280 |
500 | 457 | 1110 | 620 | 28 | 20 | M24 | 650 | 34 | 20 | M30 | 450 |